Tikkurila worldwide
产品使用说明书
27.12.2005

Duasolid 50

 
Tikkurila Industry 9L
描述 A two component oxirane ester paint containing active anti-corrosive pigments.
产品特性 Used as a single coat or as a topcoat in oxirane ester based systems on steel surfaces exposed to abrasion and chemicals in severe climatic conditions.
推荐用途 Suitable for earth moving machines, haulage and lifting equipment, forklifts, agricultural machinery, electric appliances, pumps and other steel structures, equipment and machinery.

技术参数
特性 Excellent durability. Environmentally more friendly and for users more safe alternative than epoxy and polyurethane paints. High volume solids. High film build properties, up to 100 µm / one coat.
色卡 RAL, NCS, SSG, BS, MONICOLOR NOVA and SYMPHONY colour cards. TEMASPEED tinting. Gloss varies depending on the used hardener, see application.
涂布率

Recommended film thicknesses approx.

Theoretical coverage approx.

dry

wet

 

60 µm

95 µm

10.6 m2/l

100 µm

160 µm

6.4 m2/l


Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated.
混合比例 Base 2 parts by volume 527-series
Hardener 1 part by volume 008 7675 (55904), other hardeners: see apllication
涂刷方法 By airless, conventional or electrostatic spray
适用期 8 hours
干燥时间

DFT 80 µm

+ 23 ºC

Dust dry, after

30 - 60 min

Touch dry, after

4 - 6 h

Dry to handle, after

8 - 12 h

Recoatable with other Duasolid 50 paints, after

a few min

Through dry at  increased temperature after 45 min / 80 ºC.


Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation.
Solids volume approx. 65 ± 2 volume %
密度 approx. 1.5 kg / l
产品编号 527-series

使用说明
施工条件 All surfaces must be dry. The temperature of the ambient air, surface or paint itself should not fall below +10 ºC during application or drying. Relative humidity should not exceed 80 %. The surface temperature of the steel should remain at least 3 ºC above the dew point.
准备 Oil, grease, salts and dirt are removed by appropriate means. (ISO 12944-4)

Steel surfaces: Blast clean to grade Sa2½. (ISO 8501-1) If blast cleaning is not possible, phosphating is recommended for cold rolled steel to improve adhesion.

Primed surfaces: Oil, grease, salt and dirt are removed from the surface by appropriate means. Repair any damage to the primer coat. Note the overcoating time of primer. (ISO 12944-4)
涂刷底漆 DUASOLID PRIMER and DUASOLID 50.
喷面漆 DUASOLID 50.
涂刷 By airless, conventional or electrostatic spray. At airless spray application the paint can be thinned if necessary to a viscosity of 20 s DIN 4. Airless spray nozzle tip "0.013 - 0.015", pressure ratio at least 30:1 and nozzle pressure 160 - 200 bar. Atomization air pressure 2 - 4 bar. At conventional spray application the viscosity should be 20 - 40 s DIN 4 and at electrostatic spraying 20 s DIN 4.

Properties and gloss of DUASOLID 50 will vary according to the used hardener:

Hardener 008 7675 (55904) gloss abt. > 70 mixing ratio 2:1
Hardener 008 7670 (55953) gloss abt. >70 mixing ratio 2:1
Hardener 008 7665 (55911) gloss abt. 60 mixing ratio 2:1
Hardener 008 7667 (55917) gloss abt. 10 mixing ratio 2:1
Hardener 008 7672 (55939) gloss abt. 40 mixing ratio 2:1
Hardener 008 7666 (55907) gloss abt. > 70 mixing ratio 8:5
Hardener 008 7668 gloss abt. < 10 mixing ratio 2:1

Avoid hot spray!
成分混合 First stir base and hardener separately. The correct proportions of base and hardener must be mixed thoroughly before use. Use Temaspeed Squirrel Mixer for mixing.
工具清洗 Thinner 1048 or Thinner 1112.
EU VOC 2004/42/EC-限值 The Volatile Organic Compounds amount is 320 g/litre of paint mixture.
VOC content of the paint mixture (thinned 15 % by volume) is 399 g/l.

健康安全等级
Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oy.
 
-


返回