Temabond WG 200

产品使用说明书
24.02.2006

Temabond WG 200

描述

A two component, low temperature curing, aluminium pigmented high-solids modified epoxy paint.

产品特性

Especially used as a primer for steel surfaces difficult to clean in process and chemical industry and in water immersion. Excellent adhesion to blast cleaned or hand prepared steel. Recommended for repairing of damages caused by transport or installation. Can also be applied on old alkyd paint surfaces and as a single coat paint.

推荐用途

Recommended for repainting and touch-up painting of bridges, cisterns and different types of steelwork and equipment in wood-processing and chemical industry, such as paper machines, conveyors, tubular bridges etc.

技术参数

特性

Good chemical, solvent and abrasion resistance, due to the aluminium pigments. High film build properties, also by brush. Low solvent content - lower solvent emissions than with traditional epoxy paints.

色彩类别

Aluminium. The colour will change in outdoor use.

光泽组别

半光

涂布率

Recommended film thicknesses		Theoretical coverage
dry	wet
100 µm	125 µm	8.0 m²/l
200 µm	250 µm	4.0 m²/l

Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated.

混合比例

Base 1 part by volume 008 7510
Hardener 1 part by volume 008 7519

涂刷方法

By airless spray or brush.

适用期

1½ hours

干燥时间

DFT 150 µm	-5 ºC	0 ºC	+ 5 ºC	+ 10 ºC	+ 23 ºC
Dust dry, after	18 h	14 h	6 h	3 h	2 h
Touch dry, after	48 h	36 h	17 h	9 h	5 h
Recoatable, min. after	48 h	36 h	17 h	9 h	5 h
Recoatable without sanding, max. after	2 months	2 months	2 months	1 month	14 d

Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation.

Solids volume

80 ± 2 volume % (ISO 3233)
83 ± 2 weight %

密度

1.3 kg / l (mixed)

产品编号

008 7510

使用说明

施工条件

All surfaces must be dry. The temperature of the ambient air and the surface should not fall below - 5 ºC during application and drying, the temperature of the paint should be at least +15 ºC. Relative humidity should not exceed 80 %. The surface temperature of the steel should remain at least 3 ºC above the dew point.

准备

Oil, grease, salts and dirt are removed by appropriate means. (ISO 12944-4)

Steel surfaces: Remove rust by tool cleaning to minimum St2 or blast clean to Sa2½ . Blast clean to grade Sa2½ for immersion. (ISO 8501-1).

Earlier painted surfaces: Roughen old paint surfaces using e.g. abrasive wheel, sand paper or blast cleaning.

涂刷底漆

TEMABOND WG 200.

喷面漆

TEMACOAT GPL, TEMACOAT GPL-S MIO, TEMACOAT GPL-S PRIMER, TEMACOAT GS 50, TEMACOAT RM 40, TEMADUR, TEMATHANE, TEMACRYL EA, TEMABOND WG 300 and ST 300.

涂刷

By airless spray or brush. Depending on the temperature of the components the paint can be thinned 0 - 10 %. Airless spray nozzle tip 0.013" - 0.019" and nozzle pressure 120 - 180 bar. Spray angle shall be chosen according to the shape of the object. At brush application the paint should be thinned according to the circumstancies.

成分混合

First stir base and hardener separately. The correct proportions of base and hardener must be mixed thoroughly before use. Use Temaspeed Squirrel Mixer for mixing.

工具清洗

Thinner 1031.

EU VOC 2004/42/EC-限值

The Volatile Organic Compounds amount is 220 g/litre of paint.
VOC content of the paint mixture (thinned 10 % by volume) is 280 g/l.

健康安全等级

Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oy.

上述信息，基于实验室测试和实际应用而获得，产品使用说明书记载了其被验证有效的日期，我们的生产体系通过了ISO9001和ISO14001认证，可充分保证该产品的质量。对不按使用说明施工和产品用于不当场合所带来的任何损失，作为生产商，我们不会承担任何责任。