Temacoat GPL

产品使用说明书
23.03.2006

Temacoat GPL

描述

A two component, amine adduct cured epoxy finish.

产品特性

Used especially as a finishing coat in epoxy systems exposed to heavy abrasion and/or chemical stress. Also suitable for concrete floors.

推荐用途

Recommended for bridges, tanks and different types of steelwork and equipment in the wood processing and chemical industries, such as tubular bridges, conveyors, paper machines etc.

技术参数

特性

Withstands +150 ºC dry heat and + 60 ºC in immersion. Withstands immersion in dilute solutions of non-oxidizing acids, alkalis and salts. Resists only temporary splashes of oxidizing acids and bleaching solutions. Withstands chemically active gases and dust. Withstands immersion in mineral/vegetable/animal fats and oils.

色卡

RAL, NCS, SSG, BS, MONICOLOR NOVA and SYMPHONY colour cards. TEMASPEED tinting.

光泽组别

光

涂布率

Recommended film thicknesses		Theoretical coverage
dry	wet
50 µm	90 µm	11.0 m²/l
100 µm	185 µm	5.5 m²/l

Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated.

混合比例

Base 3 parts by volume 170-series.
Hardener 1 part by volume 008 7580

涂刷方法

By airless spray or brush.

适用期

5 hours

干燥时间

DFT 60 µm	+ 10 ºC	+ 23 ºC	+ 35 ºC
Dust dry,after	3 h	2 h	1 h
Touch dry, after	10 h	5 h	2 h
Recoatable,after	10 h	4 h	2 h
Recoatable in immersion, after	32 h	16 h	8 h

Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation.

Solids volume

55 ± 2 volume % (ISO 3233)
68 ± 2 weight %

密度

1.3 - 1.4 kg / l (mixed) depending on colour.

产品编号

170-series.

使用说明

施工条件

All surfaces must be dry. The temperature of the ambient air, surface or paint should not fall below +10 ºC during application or drying. Relative humidity should not exceed 80 %. The surface temperature of the steel should remain at least 3 ºC above the dew point.

准备

Primed surfaces: Oil, grease, salt and dirt are removed from the surface by appropriate means. Repair any damage to the primer coat. Note the overcoating time of primer. (ISO 12944-4)

Concrete surfaces: The surface must be dry and at least 4 weeks old. The relative humidity of the concrete should not exceed 97%. Remove any splashes and unevennesses by grinding. Remove laitance and form oil from concrete castings by sanding or blast cleaning. Any cracks, crevices and voids must be repaired with a mixture of TEMAFLOOR 200 and fine dry quartz sand.

涂刷底漆

TEMACOAT GPL-S PRIMER, TEMACOAT GF PRIMER, TEMACOAT HB PRIMER, TEMACOAT PM PRIMER, TEMACOAT GPL-S MIO, TEMACOAT SPA, TEMALINE LP PRIMER, TEMAMASTIC PM 100, TEMABOND and FONTECOAT EP PRIMER.

喷面漆

TEMACOAT GPL.

涂刷

By airless spray or brush. At spray application the paint should be thinned 5 - 15 %. Airless spray nozzle tip 0.011" - 0.017" and nozzle pressure 120 - 160 bar. Spray angle shall be chosen according to the shape of the object.
At brush application the paint can be thinned according to the circumstancies.

成分混合

First stir base and hardener separately. The correct proportions of base and hardener must be mixed thoroughly before use. Use Temaspeed Squirrel Mixer for mixing.

工具清洗

Thinner 1031.

EU VOC 2004/42/EC-限值

The Volatile Organic Compounds amount is 430 g/litre of paint mixture.
VOC content of the paint mixture (thinned 15 % by volume) is 495 g/l.

健康安全等级

Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oy.

上述信息，基于实验室测试和实际应用而获得，产品使用说明书记载了其被验证有效的日期，我们的生产体系通过了ISO9001和ISO14001认证，可充分保证该产品的质量。对不按使用说明施工和产品用于不当场合所带来的任何损失，作为生产商，我们不会承担任何责任。