Temanyl MS Primer

产品使用说明书
02.01.2006

Temanyl MS Primer

描述

A one component modified vinyl primer.

产品特性

Suitable for underwater steel, zinc and aluminium structures like ship bottoms etc. Used also as a primer under conventional and selfpolishing antifoulings. Can also be applied at low temperature conditions. Suitable to be used as a primer under vinyl, chlorinated rubber and acrylic topcoats.

推荐用途

Steel surfaces.

技术参数

特性

Good abrasion, immersion and atmospheric resistance.

色彩类别

Aluminium (reddish aluminium with Temaspeed tinting).

光泽组别

哑光

涂布率

Recommended film thicknesses		Theoretical coverage
dry	wet
60 µm	160 µm	6.3 m²/l
100 µm	265 µm	3.8 m²/l

Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated.

涂刷方法

By spray or brush.

干燥时间

DFT 80 µm	+ 5 ºC	+ 10 ºC	+ 23 ºC	+ 35 ºC
Dust dry, after	2 h	1½ h	1 h	½ h
Recoatable, after	6 h	4 h	3 h	2 h

Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation.

Solids volume

38 ± 2 % volume (ISO 3233)
53 ± 2 % weight

密度

1.1 kg / l

产品编号

008 6740

使用说明

施工条件

The surface has to be dry. The temperature of the ambient air, surface or paint should not fall below - 5 ºC during application and drying. During application and drying the relative humidity should not exceed 80 %. The surface temperature should remain at least 3 ºC above the dew point.

准备

Oil, grease, salts and dirt are removed by appropriate means. (ISO 12944-4)

Steel surfaces: Blast clean to grade Sa2½. (ISO 8501-1) If blast cleaning is not possible, phosphating is recommended for cold rolled steel to improve adhesion.

Zinc surfaces: Sweep blast clean with mineral abrasives, e.g. quartz sand, to an even roughness. (SaS, SFS 5873) If sweep blasting is not possible, the surface should be roughened by hand abrading or washed with FONTECLEAN ZN detergent.

Aluminium surfaces: Sweep blast clean with non-metallic abrasives to an even roughness. (SaS, SFS 5873) If sweep blasting is not possible, the surface should be roughened by hand abrading or washed with FONTECLEAN AL detergent.

Primed surfaces: Oil, grease, salt and dirt are removed from the surface by appropriate means. Repair any damage to the primer coat. Note the overcoating time of primer. (ISO 12944-4)

安装

TEMANYL MS PRIMER, TEMABOND, TEMAZINC 77, TEMAZINC 88 and TEMAZINC 99.

安装

TEMACRYL AR 50 and TEMACHLOR 40.

安装

By spray or brush. Mix the paint thoroughly before use. Depending on the application method the paint can be thinned 0 - 5 %. Airless spray nozzle tip 0.018" - 0.023", spray angle 65º - 80º and nozzle pressure 15 MPa (150 bar).

成分混合

Thinner 1006.

EU VOC 2004/42/EC-限值

The Volatile Organic Compounds amount is 540 g/litre of paint.
VOC content of the paint (thinned 5 % by volume) is 557 g/l.

健康安全等级

Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oy.

上述信息，基于实验室测试和实际应用而获得，产品使用说明书记载了其被验证有效的日期，我们的生产体系通过了ISO9001和ISO14001认证，可充分保证该产品的质量。对不按使用说明施工和产品用于不当场合所带来的任何损失，作为生产商，我们不会承担任何责任。