Temaprime EUR
|
|
描述 |
A fast drying, one component anti-corrosive alkyd primer. |
产品特性 |
Primer in alkyd systems for steel surfaces exposed to weathering. Ideal for use in assembling plants and painting stations with rapid production cycles. Can also be used without any topcoat for steel surfaces in dry indoor areas. |
推荐用途 |
Recommended for steel structures, agricultural, construction and other machinery. |
|
技术参数 |
色彩类别 |
Reddish brown (TVT 4000) and grey (TVT 4001). TEMASPEED tinting. |
光泽组别 |
哑光 |
涂布率 |
Recommended film
thicknesses
|
Theoretical
coverage
|
dry
|
wet
|
|
40 µm
|
80 µm
|
12.7 m2/l
|
60
µm
|
120
µm
|
8.5
m2/l
|
Practical
coverage depends on the application method, painting conditions and the shape
and roughness of the surface to be coated.
|
涂刷方法 |
By airless
spray or by brush |
干燥时间 |
DFT 50 µm
|
+ 10 ºC
|
+ 23 ºC
|
+ 35 ºC
|
Dust dry, after
|
40 min
|
20 min
|
10 min
|
Touch dry, after
|
1½ h
|
40 min
|
30 min
|
Recoatable, after
|
1½ h
|
40 min
|
30 min
|
Drying
and recoating times are related to the film thickness, temperature, the
relative humidity of the air and ventilation.
|
Solids volume |
51 ± 2 % volume (ISO 3233)
70 ± 2 % weight |
密度 |
1.3 kg / l |
产品编号 |
186-series |
|
使用说明 |
施工条件 |
All surfaces must be dry. The temperature of the ambient air, surface or paint should not fall below +5 ºC during application or drying. Relative humidity should not exceed 80 %. The surface temperature of the steel should remain at least 3 ºC above the dew point. |
准备 |
Oil, grease, salts and dirt are removed by appropriate means. (ISO 12944-4)
Steel surfaces: Blast clean at least to grade Sa2. Clean small damages by tool cleaning to St2. (ISO 8501-1) If blast cleaning is not possible, phosphating is recommended for cold rolled steel to improve adhesion.
Primed surfaces: Oil, grease, salt and dirt are removed from the surface by appropriate means. Repair any damage to the primer coat. Note the overcoating time of primer. (ISO 12944-4) |
涂刷底漆 |
TEMAPRIME EUR. |
喷面漆 |
TEMALAC, FONTECRYL and FONTELAC. |
涂刷 |
By airless spray or by brush. Mix the paint thoroughly before use. The paint can be thinned 0 - 15 % at airless spray application. Airless spray nozzle tip 0.011" - 0.015" and nozzle pressure 120 - 180 bar. Spray angle shall be chosen according to the shape of the object. |
工具清洗 |
Thinner 1006. |
EU VOC 2004/42/EC-限值 |
The Volatile Organic Compounds amount is 440 g/litre of paint.
Maximum VOC content in ready to use paint (thinned 15 % by volume) is 495 g/l. |
|
健康安全等级 |
|
Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets.
A health and safety data sheet is available on request from Tikkurila Oy. |
|
- |
|