Temasil 90

产品使用说明书
03.01.2006

Temasil 90

描述

A two component, ethyl silicate zinc rich paint.

产品特性

Can be used as a single coat or as a primer in protective coating systems.

推荐用途

Recommended for bridges, pipework, heat exchangers and chemical tanks etc.

技术参数

特性

Offers cathodic protection of steel. Excellent resistance to abrasion and weathering. Excellent resistance also to high, dry temperatures up to + 480 ºC. Withstands immersion in oils and various solvents. Separate chemical resistance table available.

色彩类别

Greenish grey and grey.

光泽组别

哑光

涂布率

Recommended film thicknesses		Theoretical coverage
dry	wet
60 µm	120 µm	8.5 m²/l
80 µm	160 µm	6.4 m²/l

Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated.

混合比例

Base 1 part by volume 008 7381-2
Hardener 1 part by volume 008 7380

涂刷方法

By airless or conventional spray or brush.

适用期

5 hours

干燥时间

DFT 75 µm	+ 10 ºC	+ 23 ºC	+ 35 ºC
Dust dry, after	½ h	15 min	10 min
Touch dry, after	1 h	½ h	15 min
Recoatable, RH 85 % *see overleaf, after	36 h	5 h	2 h
Recoatable, RH 70 %, after	48 h	24 h	7 h
Recoatable, RH 50 %, after	-	48 h	24 h

Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation.

Solids volume

55 ± 2 % volume

密度

2.0 kg / l (mixed)

产品编号

008 7381-2

使用说明

施工条件

All surfaces must be dry. The temperature of the ambient air or surface should not fall below -15 ºC during application and drying. Relative humidity should be 50 - 90 %. The surface temperature of the steel should remain at least 3 ºC above the dew point.

准备

Oil, grease, salts and dirt are removed by appropriate means. (ISO 12944-4)

Steel surfaces: Blast clean to grade Sa2½ - 3. (ISO 8501-1)

喷面漆

TEMACHLOR 40, TEMACRYL AR, TEMACRYL EA, TEMAL, TEMACOAT GPL-S PRIMER, TEMACOAT GPL-S MIO, TEMACOAT RM 40 and TEMACOAT SPA.

TEMASIL 90 may be overcoated with above mentioned paints when Thinner 1029 does not dissolve the coat. Before overcoating it is recommended to spray a misty coat with 25 % thinned TEMACOAT GS 50.

涂刷

By airless or conventional spray or brush. Agitate during application. Depending on the application method the paint can be thinned 0 - 5 % by volume. Airless spray nozzle tip 0.018" - 0.021" and nozzle pressure 120 - 180 bar. Spray angle shall be chosen according to the shape of the object.

When coating interiors of chemical tanks or working in dry conditions, it is recommended to rinse the paint film with fresh water 1 - 24 hours after application. Sharp edges, corners, weld seams and other areas difficult to cover properly by spray application should be coated by a brush before the spray application.

Note! There is a risk of mudcracking or peeling with heavier coats than approx. 100 µm dry film thickness.

Separate application instructions available.

成分混合

First stir base and hardener separately. The correct proportions of base and hardener must be mixed thoroughly before use. Use Temaspeed Squirrel Mixer for mixing.

工具清洗

Thinner 1029.

EU VOC 2004/42/EC-限值

The Volatile Organic Compounds amount is 470 g/litre of paint.
VOC content of the paint mixture (thinned 5 % by volume) is 480 g/l.

健康安全等级

Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oy.

上述信息，基于实验室测试和实际应用而获得，产品使用说明书记载了其被验证有效的日期，我们的生产体系通过了ISO9001和ISO14001认证，可充分保证该产品的质量。对不按使用说明施工和产品用于不当场合所带来的任何损失，作为生产商，我们不会承担任何责任。