Tikkurila worldwide
产品使用说明书
22.02.2006

Fontecoat EP Primer

 
Tikkurila Industry 9L
描述 A two component waterborne epoxy primer.
产品特性 Used as a primer for steel surfaces in epoxy and polyurethane paint systems. Can be used on ships for surfaces above water line. Can also be applied onto concrete substrate e.g. walls, plasterboard etc.
推荐用途 Recommended as a primer for haulage equipment, cranes, steel masts, conveyors and other steelwork, machinery and equipment.

技术参数
色彩类别 Red TVT 4000, grey TVT 4004 etc.
光泽组别 半光
涂布率

Recommended film thicknesses

Theoretical coverage

dry

wet

 

50 µm

105 µm

9.4 m2/l

70 µm

150 µm

6.7 m2/l


Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated.
稀释剂
混合比例 Base 1 part by volume 007 1001-5
Hardener 1 part by volume 007 1019
涂刷方法 By airless spray or brush.
适用期 1½ h
干燥时间

DFT 60 µm

+ 15 ºC

+ 23 ºC

+ 35 ºC

Dust dry, after

4 h

2 h

1 h

Touch dry, after

8 h

4 h

2 h

Recoatable by itself, after

12 h

6 h

3 h

Recoatable by solvent borne paints, after

48 h

24 h

12 h


Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation.
Solids volume 47 ± 2 volume % (ISO 3233)
60 ± 2 weight %
密度 1.3 kg / l (mixed)
产品编号 007 1001-5

使用说明
施工条件 All surfaces must be dry. The temperature of the ambient air, surface or paint should not fall below +15 ºC during application and drying. Relative humidity should not exceed 70 %. The surface temperature of the steel should remain at least 3 ºC above the dew point.
准备 Oil, grease, salts and dirt are removed by appropriate means. (ISO 12944-4)

Steel surfaces: Blast clean to grade Sa2½. (ISO 8501-1) If blast cleaning is not possible, phosphating is recommended for cold rolled steel to improve adhesion.

Primed surfaces: Oil, grease, salt and dirt are removed from the surface by appropriate means. Repair any damage to the primer coat. Note the overcoating time of primer. (ISO 12944-4)
涂刷底漆 FONTECOAT EP PRIMER and TEMACOAT GPL-S PRIMER.
喷面漆 FONTECOAT EP 50, FONTECOAT EP 80, FONTEDUR 90, TEMACOAT GPL, TEMACOAT GS 50, TEMADUR and TEMATHANE.
涂刷 By airless spray or brush. If necessary, the paint can be thinned maximum 5 %. Airless spray nozzle tip 0.011" - 0.015" and nozzle pressure 140 - 180 bar. Spray angle shall be chosen according to the shape of the object.
成分混合 First stir base and hardener separately. The correct proportions of base and hardener must be mixed thoroughly before use. Use Temaspeed Squirrel Mixer for mixing.
工具清洗 Water or a mixture of water and Thinner 1029, 1:1. The equipment must be cleaned immediately after use before the paint dries.
EU VOC 2004/42/EC-限值 The Volatile Organic Compounds amount is 60 g/litre of paint.
VOC content of paint mixture (thinned by 10 % by volume) 57 g/l.

健康安全等级
Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oy.
 
-


返回