Tikkurila worldwide
产品使用说明书
29.02.2008

Finngard 150 - Protective Coating for Concrete

Finngard 150
描述 Alkali-resistant water-borne acrylate paint, which protects concrete against humidity and carbonation. FinnGard 150 is especially suitable for concrete structures which are exposed to weathering and are free from cracking which causes structural instability (only hair-cracking is allowed). FinnGard 150 has no significant impact on the water vapour permeability of the structure. Suitable for painting of concrete surfaces such as facades, front and side panels of balconies or other exterior concrete structures.
产品特性 Suitable for painting of concrete surfaces such as facades, front and side panels of balconies or other exterior concrete structures.
推荐用途 Residential, business, industrial, storage etc. buildings, parking halls.

技术参数
  该涂料是全哑光的 该涂料是水性的 工具:辊子 工具:喷枪 工具:刷子
The coverage of the paint on rough surfaces
3
The coverage of the paint on smooth surfaces
6
色彩类别 Tikkurila Facade Colour Card.
光泽等级 全哑光
涂布率

Approx. 3 - 6 m²/l (one treatment). Coverage is determined by the roughness and porosity of the surface as well as painting method and conditions. Recommended dry film thickness is approx 150µm which is achieved after 2-3 treatments.

包装型号 9 l, 18 l
稀释剂
涂刷方法

Brush, roller or spray. High pressure application: -Min.nozzle size 0.027 ( 0.62 mm), can be thinned 0-10 % if necessary

温度23度,相对湿度为50%时的干燥时间

Recoatable after 12 hours.

二氧化碳扩散阻力

Sd, CO2> 225 m when the dry film thickness of the paint coats is 150 µm.

水汽阻力(EN ISO 7783) Sd, H2O < 0.5 m when the dry film thickness of the paint coats is 150 µm.
粘合强度(ISO 4624) ≥ 0,8 N/mm2.
耐候性 Good, also in maritime and industrial atmosphere.
Solids volume n. 45%
密度 n. 1,4 - 1,6 kg/l, ISO 2811.
储存 Protect from frost.
产品编号 352

使用说明
施工条件 The surface to be treated has to be clean, the temperature of the air at least +5 °C, and the relative humidity of the air below 80 %.
准备 New concrete surfaces:
Remove dirt, loose material and salts from unpainted concrete surfaces. Pre-cast concrete surfaces can be painted after the first heating season. External grade concrete (≥K40) dries very slowly and therefore special attention must be paid to the moisture content of such elements. Surfaces cast using formwork must be mechanically worked (e.g. sand-blasted) to create sufficient texture and remove the glass-like, glossy hydrated cement. Similarly, the cement paste on cast surfaces must be removed by sand-blasting, steel brushing or high-pressure washing with the addition of sand.

Previously painted concrete surfaces:
Remove the old coating or paint with sand-blasting. Remove any loose or damaged concrete. Use a chipping hammer to expose any rusty reinforcement and clean at least to St 2 requirements. Remove all the grinding dust and chipping waste with care. Apply the Finnseco-KOR anticorrosion paint to the cleaned reinforcement and carry out the necessary repairs using the Finnseco repair mortars as instructed. Level the sand-blasted concrete surface with Finnseco Polytop finishing mortar before painting. Cure the Finnseco Polytop finishing mortar with clean water according to the instructions before starting the painting work.

Check the condition of the pre-cast concrete joints and do necessary repair work.

表面处理 First treatment:
Stir FinnGard 150 well before use. Reserve enough paint from the same batch for one uniform surface, to avoid possible colour differences. Always apply two coats. The paint can be thinned up to 5-10% with water for priming, if necessary. Finish with unthinned paint. Follow the recommended coverage values to ensure maximum protective effect. Adjust overlapping to structural details, windows, joints of elements etc.
工具清洗 Clean tools with water.
维护指导 Avoid cleaning for a month. After that, the surface can be cleansed carefully with a high pressure cleaner without detergent. The cleaning can leave permanent mark on the surface so, carefully wash according to joints. Remove loose dirt lightly with a brush without rubbing.
Apply Tikkurila Mould Removal to remove mould or algae. Rinse well.
Note! After using Tikkurila Mould Removal always recoat the surface.
维护处理 Maintenance painting:
Surfaces painted with FinnGard 150 can be re-painted with FinnGard 150. Check the condition of the structures and do necessary repair work before maintenance painting.
EU VOC 2004/42/EC-限值 (Cat A/c) 40 g/l(2010)

健康安全等级 The product is not classified as dangerous. A Material Safety Data Sheet is available on request. Material Safety Data Sheet - Finngard 150

环境保护与废弃物回收 Empty cans should be recycled or disposed of in accordance with local regulations. Liquid waste should be destroyed according to the local regulations.
运输
ssa290208 / ars200308 / jar110308 / uha261004 / / 352- ssa290208 / ars200308 / jar110308 / uha261004 / / 352- ssa290208 / ars200308 / jar110308 / uha261004 / / 352-